Painting a car with his hands

Mazda - car, loving care and comfortable service. This directly applies to the painting. And who, if not favorite car owner will be able to do it at the highest level? Of course, do not forget about the general rules and some schemes, preferably during the painting of the car at home to avoid further confusion and make beautiful mazda into a monster. First: Before you start any action on the painting, you need to wash the car, and once again to clarify - it really necessary to paint or you can leave everything as is. Washing, of course, is their own hands and simultaneously check pillar, bottom and other details on the need for repair. If any item requires intervention or change, then the painting should be postponed. Second. Necessary to prepare the body. Using screwdrivers, pliers and other essential tools necessary to untwist and remove all the body parts (locks, gaskets, moldings and other) that should not be painted. After this time-consuming occupation's turn to clean the body from corrosion. If, however, found a hole from rust - then there will only welding. Next, the third stage - a primer. It is a corrosion-resistant coating and is divided into three stages. The first phase - phosphate metal. The second stage - the primer used for alignment, thereby smoothing the microscopic defects and the surface prepared for varnishing. The third stage - gives presentation covering. Now the surface is ready to spray enamel. And thus - the fourth step of directly applying the enamel. Should pay attention to the options for paints: - simple, single layer - double layer - Metallic and pearl, which will look at this sleek and modern cars, such as mazda, very succinctly. For painting at home is better to use acrylic based paint, since it does not require high temperatures during drying. And this is important because, for quality painting requires three layers of paint that should not be dry for a long time. And last, the fifth stage - finishing. After the surface has dried, it needs polishing. After polishing acrylic lacquer is applied and the surface is dried again. Following this, at first glance is not complicated, but actually quite tedious and requires more time steps, you can upgrade mazda and a positive result for a long time to be proud of the results of their labor, because manual work is always a special price.

Read More

Starter repair in 2109 with his own hands

As such, the starter is responsible for starting the action of the apparatus. The car starter is in an internal combustion engine. His appointment in the car - roll out the crankshaft to start the engine. As you know, the car's engine operates on the basis of unwinding elements. Consequence of a broken starter motor can be for example a couple of the stronger sex, pushing the car under your window. This four-pole DC motor chetyrehschetochny gets excited mixed way. In an important part of the starter is a device for information and breeding of starter drive gear. Flywheel - with a ring gear. The starter is on the right side of the engine and is attached to the clutch three bolts. Starter VAZ has high resistance to external factors and it is easy to chinitsya. Self-starter needed replacing key "to 10". First you need to detach the bolts to the starter. Need a lower bolt (located in a remote place). Bolt is withdrawn. Intake of warm air to shoot (the key "to 13"). It is necessary to remove the nuts from the upper mounting panel (panel is installed to protect the starter from the effects of hot air). Withdrawn shield. The same key "to 13" detached two upper mounting bolts starter. Lower bolt at the bottom of the car, it is also necessary to remove the bolt. Block on the output of the traction relay disconnected after starter slightly pushed forward. Nut wires unscrew it to split pulling the starter relay with the sign "+" batteries. Clutch and the intake pipe is passed starter at withdrawal, if I pull it up. The new starter set is similar in reverse order. Replacing the starter will cost in the 1000-1500 rubles. Is there any possibility to repair the starter itself? Contamination of the starting relay - one of the most common breakdowns starter. Pulling the relay is attached nut. To weaken it, need a key "to 13". Once the nut is loosened, the tip of the wire to disconnect. Next - you need a voltage of +12 V output relays. "Less" has to go to ground, and ohmmeter joins the mounting bolts. In the healthy switch after this action puts the anchor overrunning clutch in the box front cover. Three screws to unscrew a Phillips screwdriver. Pulling the relay is removed. Switch housing contains a traction rod with a spring that you want to get. Installing a new traction relay takes place in reverse order. After replacing the starter relay starter analyzed further using a Phillips screwdriver. The cover is removed. Check the brushes by unscrewing with a screwdriver slotted screw on the contact wire. Carefully pressing out the spring, you can retrieve the brush. If the brush zanoshena above 12 mm, it must be replaced. To the stator joins ohmmeter. Retaining ring is removed with a screwdriver. After removing the axle from the washer to loosen the two screws on the key "to 10". No bolts building starter disconnected. After removal of the tubes coupling bolts tested winding. Anchor also should not be burnt. Small errors are removed from the anchor cloth and then polished.

Read More